Currency - $  
HS1900 ESP8285 WiFi module ESP-M3 serial wireless transparent transmission control module is fully compatible with ESP8266

HS1900 ESP8285 WiFi module ESP-M3 serial wireless transparent transmission control module is fully compatible with ESP8266

Brand:Haitronic
Product Code:HS1900
Availability:9999
Qty:     - OR -   Add to Wish List Add to Compare

HS1900 ESP8285 WiFi module ESP-M3 serial wireless transparent transmission control module is fully compatible with ESP8266

AT firmware:

This firmware only supports AT commands to operate the module.

Transparent transmission firmware:

This firmware configures the module through the web page, similar to the router configuration

 

 What is the ESP8285?

· ESP8285=ESP8266+1M FlashTo make it resistant to high temperatures125 degrees Celsius!And the original ESP8266 source program can be used as it is..

· The core processor of the ESP-M3 module uses the cost-effective chip ESP8285. The chip integrates an enhanced version of Tensilica's L106 Diamond Series 32-bit core processor in a smaller package with on-chip SRAM. The ESP8285 has a full Wi-Fi network function, which can be used independently or as a slave to other host MCUs. When the ESP8285 hosts an application, it can be launched directly from external Flash. The built-in cache helps improve system performance and optimizes the storage system. In addition, the ESP8285 can be used as a Wi-Fi adapter via the SPI/SDIO interface or I2C/UART port for any microcontroller-based design.

 

 

1) The volume is too small;

2) Serial port to WiFi;

3) Wireless transparent transmission;

4) Ultra-low power consumption over long distances;

5) high temperature resistance up to 125 ° C;

6) Fully compatible with ESP8266, the source code can be used as it is.

 

 

SOCcharacteristic

· Built-in Tensilica L106 ultra-low power 32-bit microprocessor with 80MHz and 160MHz frequency support, RTOS support

· Built-in TCP/IP protocol stack

· Built-in 1 10 bit high precision ADC

· Peripheral interface HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO

· Deep sleep keeps current at 10uA and shutdown current is less than 5uA

· Wake up, connect and pass packets within 2 ms

· Standby power consumption is less than 1.0mW (DTIM3)

· Built-in 1Mbyte SPI Flash

Wi-Ficharacteristic

· Support for 802.11 b/g/n/e/i

· Support Station, SoftAP, SoftAP+STA mode

· Support for Wi-Fi Direct (P2P)

· Supports hardware acceleration of CCMP (CBC-MAC, counter mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC

· P2P discovery, P2P GO mode/GC mode and P2P power management

· WPA/PA2 PSK and WPS

· 802.11 i security features: pre-authentication and TSN

· Support for 802.11n (2.4 GHz)

· 802.1h/RFC1042 frame packing

· Seamless roaming support

· Support AT remote upgrade and cloud OTA upgrade

· Support for Smart Config (including Android and iOS devices)

Module peripheral

· 2xUART

· 1xADC

· 1xEn

· 1x wake-up pin

· 1xHSPI

· 1xI2C

· 1xI2S

· Up to 10xGPIOs

range of working temperature:-40°C-125°C

Module size:26.8mm*16mm

Application scenario

● Household appliances ● Home automation

● Smart sockets, smart lights ● Mesh network

● Baby monitor ● IP camera

● Sensor network ● Wearable electronics

● Security ID tag ● Wireless location awareness

● Wireless positioning system beacon ● Industrial wireless control 

 

  

Write a review



Note: HTML is not translated!

Bad           Good